C-41CMitutoyo reserves the right to change any or all aspects of any product specication, including prices, designs and service content, without notice.• Capable of ID (inside diameter) measurement close to the bottom of a hole.• Carbide contact point ensuring high durability and wear resistance.• Grip is large and hollow to reduce effect of body heat on high-accuracy measurements.• The indicator (dial indicator, Digimatic indicator) and dial protection cover are optional. Select an indicator from the recommended dial indicators and Digimatic indicators. Please contact us for advice when using an indicator other than the recommended indicators.• Optional Extension Rods can be attached for measuring deep holes. (For details, refer to page C-45.)• A Bore Gage Checker and a range of Setting Rings are available to aid in accurately setting a gage before making a measurement. (For details, refer to pages C-46 and C-47.)Bore GagesSERIES 511 — for Blind Holes15-35 mm/0.6-1.4 in35-60 mm/1.4-2.4 in50-150 mm/2.0-6.0 inBore GagesFor easy and accurate measurement of inside diametersTechnical Data• Accuracy:Metric models 4 μmInch models 0.00016 in• Repeatability:Metric models 1 μmInch models 0.00004 in• Adjacent error:Metric models 1 μmInch models 0.00004 inOptional Accessories• Dial indicator (See Chapter F)• Dial protection cover: 21DZA000Recommended Dial Indicators (see Chapter F)• Metric models:2046SB (0.01 mm)2972TB (0.01 mm - One-revolution type)2109SB-10 (0.001 mm)2900SB-10 (0.001 mm - One-revolution type)• Inch models:2922SB (0.0005 in)2977TB (0.0005 in - One-revolution type)2923SB-10 (0.0001 in)2910SB-10 (0.0001 in - One-revolution type)Recommended Digimatic Indicators (see Chapter F)• Metric models:543-310B (0.001 mm)• Inch models:543-312B (0.001 mm/0.00005 in)Note: Indicators equipped with rubber bellows, such as water-proof types, cannot be used.Note 1: A 10 mm (0.4 in) sub-anvil is supplied with 511-415/425/435/418/428/438 and a 50 mm (2 in) sub-anvil is supplied with 511-417/427/437/420/430/440.Note 2: It is not permissible to use a sub-anvil other than as supplied as a standard accessory, or widen a measuring range by using multiple sub-anvils. (The measurement accuracy in such cases is not guaranteed.)SPECIFICATIONSMetricOrder No.Range (mm)Stroke of contact point (mm)Measuring force (N)Guide force (N)Content of setProbing depth (mm)Bore gageDial indicatorDial protection coverAnvilWasher511-41515 - 351.24 or less6 or less511-415Not suppliedNot supplied11 pcs.1 pc.150511-41635 - 60511-4166 pcs.4 pcs.511-41750 - 1505 or less10 or less511-41711 pcs.511-42515 - 351.24 or less6 or less511-4152046SB(Graduation: 0.01 mm)21DZA00011 pcs.1 pc.150511-42635 - 60511-4166 pcs.4 pcs.511-42750 - 1505 or less10 or less511-41711 pcs.511-43515 - 351.24 or less6 or less511-4152109SB-10(Graduation: 0.001 mm)21DZA00011 pcs.1 pc.150511-43635 - 60511-4166 pcs.4 pcs.511-43750 - 1505 or less10 or less511-41711 pcs.InchOrder No.Range (in)Stroke of contact point (in)Measuring force (N)Guide force (N)Content of setProbing depth (in)Bore gageDial indicatorDial protection coverAnvilWasher511-4180.6 - 1.40.0474 or less6 or less511-418Not suppliedNot supplied11 pcs.1 pc.6511-4191.4 - 2.4511-4196 pcs.4 pcs.511-4202.0 - 6.05 or less10 or less511-42011 pcs.511-4280.6 - 1.40.0474 or less6 or less511-4182922SB (Graduation: 0.0005 in)21DZA00011 pcs.1 pc.6511-4291.4 - 2.4511-4196 pcs.4 pcs.511-4302.0 - 6.05 or less10 or less511-42011 pcs.511-4380.6 - 1.40.0474 or less6 or less511-4182923SB-10 (Graduation: 0.0001 in)21DZA00011 pcs.1 pc.6511-4391.4 - 2.4511-4196 pcs.4 pcs.511-4402.0 - 6.05 or less10 or less511-42011 pcs.Note: The dial indicator and protection cover are optional. Contact Points(Unit: mm)511-416511-415511-416511-417511-4172.52.5

元のページ  ../index.html#214