L-11Mitutoyo reserves the right to change any or all aspects of any product specication, including prices, designs and service content, without notice.• FORMTRACER Avant D3000/4000 series are highly functional and user-friendly surface roughness and contour measuring systems with innovative design features. Both surface roughness measurement and contour measurement are available on a single system just by replacing the detector.• A detector can be replaced easily without turning off the power and without needing a tool just by using the thumb-turn clamp lever, and the new contour/roughness detector is automatically recognized. This quick changeover minimises downtime and improves useability by removing concerns about detector malfunction from forgetting to operate a detector switch and about damage to the detector from the malfunction.• Often a special method of workholding, such as a custom jig, is required to measure an inclined workpiece surface but this is not needed if you select a model from the FORMTRACER Avant D3000/4000 series since these have an inclining drive unit to handle this situation. This feature makes approaching the target surface and measurement of a large workpiece much easier.• The new style remote box has been developed in pursuit of operational usability. An overdrive knob controls the drive speed in real time and is very convenient when fine positioning is required. Another new feature is a part program key that strongly supports creation of measurement part programs, including a move command for manual operation and a measurement start command.• High throughput is achieved thanks to high drive speed (X axis: Max. 80 mm/s, Z2 axis: Max. 30 mm/s) and acceleration (X axis: 30 mm/s2).• All connecting cables are contained within the measuring instrument to eliminate any inconvenience during measurement.• Since the Z1-axis detector incorporates an anti-collision safety device, the detector unit will automatically stop even if it touches a workpiece or fixture.• A detector for measuring contours can be retrofitted.• The arm of the detector for contour measurement has a magnetic one-touch detachable mechanism that improves usability.• D4000 type is a highly functional contour measuring system that has a digital detector (measuring range: 60 mm, resolution: 0.02 µm) that enables a wide range measurement, top/bottom plane continuous measurement function, automatic variable measuring force function and stylus drop detection function.SPECIFICATIONSModel No.FTA-S4D3000FTA-H4D3000FTA-W4D3000FTA-L4D3000FTA-S8D3000FTA-H8D3000FTA-W8D3000FTA-L8D3000FTA-S4D4000FTA-H4D4000FTA-W4D4000FTA-L4D4000FTA-S8D4000FTA-H8D4000FTA-W8D4000FTA-L8D4000Surface roughness measurementMeasuring rangeX axis100 mm200 mmZ1 axis 800 µm, 80 µm, 8 µmStraightness(when the X axis is horizontal)(0.05+0.001L) µm L = Measurement Length (mm)(0.1+0.002L) µm L = Measurement Length (mm)Contour measurementMeasuring rangeX axis100 mm200 mmZ1 axis 60 mm (±30 mm in horizontal situation)Straightness (when the X axis is horizontal)0.8 µm/100 mm2 µm/200 mmAccuracy (20 °C)D3000X axis(0.8+0.01L) µm L = Measurement Length (mm)(0.8+0.015L) µm L = Measurement Length (mm)Z1 axis (detector unit)±(1.2+|2H|/100) µm H = Measurement height from the horizontal position (mm)D4000X axis(0.8+0.01L) µm L = Measurement Length (mm)(0.8+0.015L) µm L = Measurement Length (mm)Z1 axis (detector unit)±(0.8+|2H|/100) µm H = Measurement height from the horizontal position (mm)Common specificationsX-axis inclination angle±45°Z2-axis (column) travel range300 mm500 mm700 mm300 mm500 mm700 mmBase size (W×D)600×450 mm1000×450 mm600×450 mm1000×450 mmBase materialGraniteNote: While the appearance of the natural stone measuring table varies according to the source, the high stability for which this material is known can always be relied upon.Remote box with user-friendly operabilityDetectorDetector holder (optional)Large sized base models and high-column models are added to the line-up.FTA-S4D3000(Detector for surface roughness measurement equipped, with monitor arm)FTA-S4D3000(Detector for form/contour measurement equipped, with monitor arm)Connecting cables are contained within the measuring instrument.For D3000For D4000An inspection certicate is supplied as standard. Refer to page U-11 for details.Products equipped with the measurement data output function can be connected to the measurement data network system MeasurLink (refer to page A-5 for details).FormtracerHybrid machine with dual-role capabilityFORMTRACER Avant D3000/4000 SeriesSERIES 525 — Surface Texture Measuring InstrumentsInclined drive unitL

元のページ  ../index.html#542