D-6DMitutoyo reserves the right to change any or all aspects of any product specication, including prices, designs and service content, without notice.FunctionsAbsolute measurement: After power is turned ON, measurement can be started without zero-setting if origin-setting was previously performed. The Absolute origin position can be changed by the ORIGIN button.Incremental measurement: Display can be set to zero at any arbitrary position for comparative measurements. Low-voltage alert: If the battery voltage becomes low, a “B” appears in the display to alert the user before measurement is no longer possible. A battery change advisory alert precedes this alert.Data output: By using the connecting cable (optional), measurement data can be output.Data hold: By using the data hold unit (optional), the displayed value can be held. This cannot be used with the data output function.SPECIFICATIONSMetricOrder No.Range (mm)Maximum permissible error (mm)*2Mass (g)Depth barFine adjustmentRemarksEMPESMPE500-150-300 - 100±0.02±0.04143ø1.9 mm rodwith thumb roller—500-180-30*1—500-151-300 - 150168Blade with thumb roller500-154-30Carbide-tipped jaws for outside measurement500-155-30Carbide-tipped jaws for outside and inside measurement500-158-30ø1.9 mm rod—500-181-30*1Blade—500-152-300 - 200 198with thumb roller500-156-30Carbide-tipped jaws for outside measurement500-157-30Carbide-tipped jaws for outside and inside measurement500-182-30*1——500-153-300 - 300±0.03±0.05350with thumb roller*1 Without SPC data output*2 Partial Surface Contact Error, EMPE and Shift Error, SMPE are terms (notations) used in ISO 13385-1:2019.Inch/MetricOrder No.Range (in)Maximum permissible error*2Mass (g)Depth barFine adjustmentRemarksEMPESMPE500-170-300 - 4±0.001 in/±0.02 mm±0.002 in/ ±0.04 mm143ø0.075 inch rodwith thumb roller—500-195-30*1500-171-300 - 6168Blade500-174-30Carbide-tipped jaws for outside measurement500-175-30Carbide-tipped jaws for outside and inside measurement500-178-30ø0.075 inch rod—500-196-30*1Blade500-159-30*1Carbide-tipped jaws for outside measurement500-160-30*1Carbide-tipped jaws for outside and inside measurement500-172-300 - 8198—500-176-30Carbide-tipped jaws for outside measurement500-177-30Carbide-tipped jaws for outside and inside measurement500-197-30*1—500-163-30*1Carbide-tipped jaws for outside measurement500-164-30*1Carbide-tipped jaws for outside and inside measurement500-173-300 - 12±0.0015 in/±0.03 mm±0.0025 in/ ±0.05 mm350—500-167-30Carbide-tipped jaws for outside measurement500-168-30Carbide-tipped jaws for outside and inside measurement500-193-30*1—500-165-30*1Carbide-tipped jaws for outside measurement500-166-30*1Carbide-tipped jaws for outside and inside measurement*1 Without SPC data output*2 Partial Surface Contact Error, EMPE and Shift Error, SMPE are terms (notations) used in ISO 13385-1:2019.DIMENSIONS Unit: mmABCDHLHDCBALwith thumb rollerRange (mm)ABCDHL0 - 10016.52114.540161820 - 15016.52114.540162330 - 2002024.51850162900 - 3002227.519.86420404Jaw thickness: 3.5 mm for 0 to 100 mm/0 to 150 mm/0 to 200 mm models and 3.8 mm for 0 to 300 mm modelWith thumb rollerWithout thumb roller
元のページ ../index.html#225