D-18DMitutoyo reserves the right to change any or all aspects of any product specication, including prices, designs and service content, without notice.Technical Data• Resolution:0.01 mm or 0.0005 in/0.01 mm• Material of jaws: Ceramic• Display:LCD• Scale type:ABSOLUTE electromagnetic induction linear encoder• Max. response speed: Unlimited• Battery:SR44 (1 pc.), 938882, for initial operational checks (standard accessory)• Battery life:Approx. 5,000 hours in continuous use• Dust/Water protection level: IP66 (IEC 60529)*• Standard accessory: Jaw clamps (2 pcs.), 05GZA033 * Rustproong shall be applied after use if caliper was in contact with coolant.Functions • Zero-setting• Data hold• Offsetting• Presetting• Data output• Low-power and low-voltage alert• Counting value composition error• Automatic power on/off, inch/mm reading (inch/mm models)Optional AccessoriesFor details, refer to page A-21.• Connecting cables for IT/DP/MUX 05CZA624: SPC cable with data button (1 m) 05CZA625: SPC cable with data button (2 m)• USB Input Tool Direct 06AFM380A: SPC cable for USB-ITN-A (2 m)• Connecting cables for U-WAVE-T 02AZD790A: SPC cable with data button (160 mm)02AZE140A: SPC cable for foot switchProducts equipped with the measurement data output function can be connected to the measurement data network system MeasurLink® (refer to page A-25 for details).• IP66 Absolute Digital Caliper (Refer to page D-6 for details on the Absolute function.)• Lightweight Digimatic Calipers that employ CFRP (Carbon Fiber Reinforced Plastics) in the beam.• Allows integration into statistical process control and measurement systems for models with measurement data output connector. (Refer to page A-3.)• The zirconia-ceramic jaws make this caliper suitable for measuring moderately magnetic workpieces. However, since steel is used in the main unit, it may not be suitable for measuring strongly magnetic workpieces.ABSOLUTE Coolant Proof Carbon Fiber CaliperSERIES 552 - with Ceramic Jaws552-156-10tRAEFDLHEN10 (0.25)DJ10 (0.25)SGBuilt-in constant-force mechanismSPECIFICATIONSMetricOrder No.Range (mm)*1Maximum permissible error (mm)*2EMPESMPE552-155-100 - 450 (20.1 - 470)±0.04±0.04552-156-100 - 600 (20.1 - 620)±0.04±0.04*1 ( ): Dimension in inside measurement*2 Partial Surface Contact Error, EMPE and Shift Error, SMPE are terms (notations) used in ISO 13385-1:2019.Note: A constant-force mechanism is used in the nger rest; however, this is only an auxiliary mechanism to avoid measurement error caused by excessive measuring force. To measure with good accuracy, use the minimum necessary measuring force for the caliper measuring faces to make sufcient contact with the workpiece. Refer to page D-39 for details. Inch/MetricOrder No.Range (in)*1Maximum permissible error (in)*2EMPESMPE552-165-100 - 18 (0.504 - 18.5)±0.002±0.002552-166-100 - 24 (0.504 - 24.5)±0.002±0.002*1 ( ): Dimension in inside measurement*2 Partial Surface Contact Error, EMPE and Shift Error, SMPE are terms (notations) used in ISO 13385-1:2019.Note: A constant-force mechanism is used in the nger rest; however, this is only an auxiliary mechanism to avoid measurement error caused by excessive measuring force. To measure with good accuracy, use the minimum necessary measuring force for the caliper measuring faces to make sufcient contact with the workpiece. Refer to page D-39 for details. DIMENSIONS Unit: mmRangeDEGHJLNRSt0 - 450 mm (0 - 18 in)10091.835256564041.2R101880 - 600 mm (0 - 24 in)10091.835256579041.2R10188( ): Inch/Metric type
元のページ ../index.html#237