D-69DMitutoyo reserves the right to change any or all aspects of any product specication, including prices, designs and service content, without notice.Depth GageA standard measuring tool of industry• Optimal for hole, narrow groove and step measurement.Dial Depth GageSERIES 7Typical applicationSPECIFICATIONSMetric Order No.Range (mm)Graduation (mm)Stroke (mm)Accuracy (µm)Measuring force (N)BaseContact point Note 1Extension rod Note 2Indicator Note 3(dial indicator) W (mm)T (mm)Flatness (µm)Mounting position of a dial indicator 7210A0 - 100.0110±151.4 401651Provided with a needle point (137413)—2902ABDfor Depth Gage7211A0 - 200 63.5Provided with a carbide-tipped ball point(21JAA224)5 pcs. (10, 20, 30, 30, 100 mm)2902ABDLfor Depth Gage7212A101.67213A0 - 21030±302.5 63.5Provided with a carbide-tipped ball point(21JAA225)3 pcs. (30, 60, 90 mm)2952ABDfor Depth Gage7214A101.67220A0 - 20010±151.4100182Provided with a carbide-tipped ball point(21JAA224)5 pcs. (10, 20, 30, 30, 100 mm)2902ABDLfor Depth Gage7221A15037222A0 - 10ø161Provided with a needle point (137413)—2902ABDfor Depth Gage7223Aø25Provided with a carbide-tipped ball point(21JAA224: 17 mm)7224Aø407231A0 - 200563.5165 pcs. (10, 20, 30, 30, 100 mm) Interchangeable contact point(21JAA226: 22 mm)1162ADfor Depth Gage(Back plunger type)Inch Order No.Range (in)Graduation (in)Stroke (in)Accuracy (in)Measuring force (N)BaseContact point Note 1 Extension rod Note 2Indicator Note 3 (dial indicator) W (in)T (in)Flatness (in)Mounting position of a dial indicator7217A0 - 80.0011±0.0022.02.50.630.00021Provided with a carbide-tipped ball point(21JZA242: 0.7 in)3 pcs. (1 in, 2 in, 4 in)2904ABDfor Depth Gage7218A47237A0.21.42.54 pcs. (0.5 in, 1 in, 2 in, 4 in)Interchangeable contact point(21JZA243: 0.9 in)1168ADfor Depth Gage(Back plunger type)7238A4PrecautionsNote 1Caution should be exercised when exchanging a contact point of a Depth Gage (Dial/Digimatic Indicator):• If a different size contact point is mounted, displacement of the contact point from the base contact surface will be changed and as a result, measurement range may not be maintained.• A contact point cannot be mounted to a Depth Gage if its diameter is too large for the hole diameter of the base. • Parallelism adjustment with the bottom face of the base is required when mounting a at contact point such as the at/needle or carbide-tipped contact point.Note 2Caution should be exercised when using an extension rod:• If the total length of the extension rod exceeds 110 mm (4.5 in) use the instrument in a vertical position (contact point downward).• Use a master gage (such as gauge blocks) to perform zero-setting when the extension rod is mounted. (Master gage is an optional accessory.)Note 3Caution should be exercised when indicators are used on a Depth Gage: • When the indicator is exchanged and a longer extension rod is connected, the contact-point may deect signicantly with an adverse effect on measuring accuracy.• Order No.543-400B/543-402B for Depth Gage has a measuring force less than 1.5 N.Extension rodContact pointMaster gage(optional accessory)●No.7220A、7221Aはダイヤルゲージの 取付位置を変えることができます。7220A and 7221A allow the mounting position of a dial indicator to be varied.7211A7224A7231A7214A7222A
元のページ ../index.html#288