F-8FMitutoyo reserves the right to change any or all aspects of any product specication, including prices, designs and service content, without notice.Inch/MetricOrder No. (w/lug, at-back)Range (in)ResolutionMaximum permissible error*1Measuring force MPL (N)MPEE*3Hysteresis MPEHRepeatability MPER543-391543-391B0.50.0005/ 0.0001/0.00005 in0.01/ 0.001 mm (selectable)±0.0001 in /0.003 mm0.0001 in /0.002 mm0.0001 in /0.002 mm1.5 or less543-392543-392B1.5 or less543-395*2543-395B*20.4 to 0.7543-396*2543-396B*20.4 to 0.7—543-471B11.8 or less*4—543-472B1.8 or less*4—543-491B2±0.0002 in /0.005 mm2.3 or less*4—543-492B2.3 or less*4543-401543-401B0.50.0005 in/ 0.01 mm±0.001 in /0.02 mm0.001 in /0.02 mm0.0005 in /0.01 mm0.9 or less543-402543-402B0.9 or less543-405*2543-405B*20.2 to 0.5543-406*2543-406B*20.2 to 0.5—543-475B11.8 or less*4—543-476B1.8 or less*4—543-495B2±0.0015 in /0.04 mm2.3 or less*4—543-496B2.3 or less*4*1 These values apply at 20 °C.*2 Low measuring force*3 Error of indication for the total measuring range*4 Applies for a spindle orientation between the spindle pointing vertically downward to the spindle horizontal.Note: Regarding origin setting, refer to “Origin Setting of Digimatic Indicators” on page F-25.SPECIFICATIONSMetricOrder No. (w/lug, at-back)Range (mm)Resolution (mm)Maximum permissible error*1 (mm)Measuring force MPL (N)MPEE*3Hysteresis MPEHRepeatability MPER543-390543-390B12.70.001/0.01 (selectable)0.0030.0020.0021.5 or less543-394*2543-394B*20.4 to 0.7—543-470B25.41.8 or less—543-490B50.80.0052.3 or less543-400543-400B12.70.010.020.020.010.9 or less543-404*2543-404B*20.2 to 0.5—543-474B25.41.8 or less—543-494B50.80.042.3 or less*1 These values apply at 20 °C.*2 Low measuring force*3 Error of indication for the total measuring rangeNote: Regarding origin setting, refer to “Origin Setting of Digimatic Indicators” on page F-25. ISO/JIS type ASME/ANSI/AGD typeSetting measuring force on low measuring force modelsCode No.543-400（B）/543-390（B）/543-404（B）/543-394（B）Model No.ID-C1012X（B）/112X（B）/1012CX（B）/112CX（B）ø8 0-0.0097.321.21754.446.550.1ø10.92028.87.6ø59ø54513.31.7ø6.532°Ball contact (ø3)901312(threaded: M2.5×0.45)ø4.8DIMENSIONSNote: Products with an Order No. sufxed "B" have a plain back, and other models have a center-lug back. Refer to page F-61 for details of the backs.Ball contact (ø0.12)21BZB005(thread: No. 4-48UNF)ø0.191/4ø0.431.131/4ø2.13ø2.320.301.971.742.000.580.793/4ø1/4ø0.375 0 -0.0012ASME/ANSI/AGD TypeUnit: inSpindle orientationSpringWeight (approximately 0.1 N)Maximum measuring force (N)Pointing vertically downwardYesYes0.5 or lessYesNo0.4 or lessNoYes0.3 or lessNoNo0.2 or lessHorizontalYesNo0.3 or lessNote: Operation using congurations other than shown above is not guaranteed.• 543-404/404B/405/405B/406/406BSpindle orientationSpringWeight (approximately 0.1 N)Maximum measuring force (N)Pointing vertically downwardYesYes0.7 or lessYesNo0.6 or lessNoYes0.4 or lessNoNoNot guaranteedNote: Operation using congurations other than shown above is not guaranteed.• 543-394/394B/395/395B/396/396BThe measuring force of models with low measuring force can be set by combining standard accessory springs and weights.12.7 mm range modelsUnit: mmISO/JIS TypeUsable orientation• Standard models with measuring range 12.7 mm: Usable in all orientations.• Models with measuring range 25.4 or 50.8 mm: Usable between the contact point pointing downward and spindle in horizontal orientation. To use the contact point pointing upward, the auxiliary spindle spring (optional) is required.• Low measuring force model: See “Setting measuring force on low measuring force models” below.
元のページ ../index.html#349