F-14FMitutoyo reserves the right to change any or all aspects of any product specication, including prices, designs and service content, without notice.Digimatic IndicatorsComparison measuring instruments which ensure high quality, high accuracy and reliability.• The ABS (absolute) scale restores the last origin position*2 automatically when the indicator is turned on, and realizes high reliability by eliminating over-speed errors.• By using the parameter setup kit (optional) and the dedicated software, the functions and the parameters can be congured using a computer.• Equipped with a data output port that enables incorporation into measurement networking and statistical process control systems. (Refer to page A-3)*1 Tolerance judgment results cannot be output.*2 Regarding origin setting, refer to “Origin Setting of Digimatic Indicators” on page F-25.ABSOLUTE Digimatic Indicator ID-CSERIES 543 — Bore Gage TypeOptional Accessories• SPC Cable: 905338 (1 m) 905409 (2 m)• USB Input Tool Direct (2 m): 06AFM380F• Input Tool Series IT-016U (USB Keyboard Signal Conversion Type): 264-016-10 IT-007R (RS-232C Communication Conversion Type): 264-007• Connecting Cables for U-WAVE-T (160 mm): 02AZD790F For foot switch: 02AZE140F• Digimatic Mini-Processor DP-1VA LOGGER: 264-505• Parameter setup kit: 21EZA313Note: Parameter setting software (can be downloaded for free from the Mitutoyo website) is also required.Functions• Minimum value detectionNote: Peak detection 1) Sampling rate: 50 readings/sec 2) Capturing speed: 50 µm/sec (max.)• Preset (3 Preset values can be stored)• Tolerance judgment (3 sets of upper and lower limits can be stored)• Resolution selection• Analog bar resolution selection• Key lock• Display hold (when no external device is connected)• Data saving/calling (when no external device is connected)• Data output• External PC setting input• Display rotation (330°)• Low battery voltage alarm display• Error alarm displaySPECIFICATIONSMetricOrder No.Range (mm)Resolution (mm)Maximum permissible error (mm)Measuring force MPL (N)Power supplyBattery life (normal use)*4Net mass (g)MPEE*3Hysteresis MPEHRepeatability MPER543-310B12.70.001/0.01 (selectable)0.0030.0020.0021.5 or lessCR2032 ×1 pc.Approx. 1 year170Inch/MetricOrder No.RangeResolutionMaximum permissible errorMeasuring force MPL (N)Power supplyBattery life (normal use)*4Net mass (g)MPEE*3Hysteresis MPEHRepeatability MPER543-311B0.5 in/12.7 mm0.00005/0.0001/ 0.0005 in, 0.001/0.01 mm (selectable)±0.00010 in /0.003 mm0.00010 in /0.002 mm0.00010 in /0.002 mm1.5 or lessCR2032 ×1 pc.Approx. 1 year170543-312B*3 Error of indication for the total measuring range*4 Applies only if not connected to a data processor. Battery life depends on use of the indicator. Use the above value as a guide only.Note: Flat back type only.ABSOLUTE Digimatic Bore Gages, which integrate the display with a bore gage measuring unit, are also available. Refer to pages C-43 and C-44 for details.The ABSOLUTE Digimatic Bore GageAn inspection certicate is supplied as standard. Refer to page U-9 for details.Products equipped with the measurement data output function can be connected to the measurement data network system MeasurLink® (refer to page A-25 for details).543-310BTypical application The Bore Gage is optional.• Dedicated to inside measurement with minimum-value Hold and tolerance judgment functions*1. Use together with a Mitutoyo bore gage (refer to pages C-27 to C-42 for details).• Five buttons, status icons, and clear button indications allow for easy operation of a wide variety of functions.• Wide LCD and new analog bar graph are now standard on all models.• Can store up to three sets of master reference values and tolerances, alleviating the need for multiple settings to master gages. ISO/JIS type ASME/ANSI/AGD type
元のページ ../index.html#355