F-19FMitutoyo reserves the right to change any or all aspects of any product specication, including prices, designs and service content, without notice.• Enables a tolerance judgment to be output to external equipment for a measurement result against user-dened limits. Solid-state switching provides high reliability by avoiding metallic switch contacts. • Output is enabled by directly connecting to external devices (sequencers, etc., for which a logical invert is available if required). The measurement and judgment results are displayed on the LCD. The judgment result is also indicated by 2 LEDs. • A peak-detection function is equipped for measuring and judging peak values, such as runout.• Positional detection is absolute (ABS system) relative to a set origin point*1 that does not need to be reset every time power is turned on. Furthermore, the ABS system ensures that overspeed errors do not occur.• Provided with a 4 m cable.• External power supply required is 5-24 VDC/ 100 mA (max.).• Dust-water protection level: Conforms to IP54.*1 Regarding origin setting, refer to “Origin Setting of Digimatic Indicators” on page F-25.ABSOLUTE Digimatic Indicator ID-C SERIES 543 — Signal Output Function TypeDigimatic IndicatorsComparison measuring instruments which ensure high quality, high accuracy and reliability.543-350SPECIFICATIONSMetricOrder No. Range (mm)Resolution (mm)Maximum permissible error (mm)Measuring force MPL (N)Net mass (g)MPEE*2Hysteresis MPEHRepeatability MPER543-35012.70.001/0.01(selectable)0.0030.0020.0022.5 or less290543-350B285Inch/MetricOrder No. RangeResolutionMaximum permissible errorMeasuring force MPL (N)Net mass (g)MPEE*2Hysteresis MPEHRepeatability MPER543-3510.5 in /12.7 mm0.00005/0.0001/0.0005 in, 0.001/0.01 mm(selectable)±0.00010 in /0.003 mm0.0001 in/0.002 mm0.0001 in/0.002 mm2.5 or less295543-351B285543-352295543-352B285*2 Error of indication for the total measuring rangeNote 1: LCD readout does not rotate.Note 2: MAX/MIN holding: sample rate is 100 readings/s; max. rate of change of reading is 100 μm/s or less.Note 3: Products with an Order No. sufxed “B” have a at backNote 4: Standard contact point: 901312 (ISO/JIS type), 21BZB005 (ANSI/AGD type)Functions• Signal output (–NG/OK/+NG, N-ch open drain, logical invert is available)• Remote control (peak start preset/zero-set)• Peak detection (MAX/MIN)• Runout range measurement (MAX - MIN) • Zero-setting (INC system)• Presetting (ABS system)• Direction switching• Tolerance judgment (3 pairs of ABS, INC memory function)• Resolution switching • Calculation: f(x) =Ax• Key lock• Calibration mode (Signal output in Digimatic code format)• Error alarm displayOptional Accessories• Lifting*1 Lifting lever21EZA198 (ISO/JIS Type), 21EZA199 (ASME/ANSI/AGD Type) Lifting cable21JZA295 Lifting knob21EZA105 (ISO/JIS Type), 21EZA150 (ASME/ANSI/AGD Type)• Digimatic power supply unit: 21EZA345 To denote your AC power cable add the following sufxes to the order No.: A for UL/CSA, D for CEE, DC for CCC, E for KC. No sufx is required for JIS/100VAC.Used in the calibration mode when executing automatic inspection using i-Checker IC2000.In such a case, purchase connecting cable21EAA194 (1 m), or 21EAA190 (2 m). Note: It can’t be used as a power suppy when using in the normal mode. • Contact points for Mitutoyo’s dial indicators.*2• Measuring stands (Refer to pages F-84 to F-91 for details.)*1 Dust-water protection is not guaranteed.*2 Refer to pages F-57 to F-60 for details.WireSignalI/ODescriptionBlack– V (GND)—Connected to minus (-) terminalRed+ V—Power supply (5 to 24 VDC)Orange– NGOTolerance judgment result output: Only the terminal corresponding to a judgment result is set to the low level.GreenOKOBrown+ NGOYellowPRESET_RECALLZEROIExternal input terminal: If the relevant terminal is set to the low level, its signal becomes true.BluePEAK_STARTIShieldFG—Connected to GND (Earth)Note: Measurement data cannot be output.I/O SpecicationsWire– NGOK+ NGABS data composition errorOrange (– NG)LowHighHighHighGreen (OK)HighLowHighHighBrown (+ NG)HighHighLowHighLEDRedGreenRedRed ashingLCD“x.xxE” indicationNote: Logical invert is available.Output signals and LCD displayOUTInputOutputcircuits (Orange, Green, Brown)OutputOUT5 to 24 VDC1.2 kΩLoadGNDLoad voltage: 5 to 24 VDCMax. load current: 100 mA or lessInput current: Max. 20 mAGNDSwitch, etc.External powerINInternal circuitInternal circuitAn inspection certicate is supplied as standard. Refer to page U-9 for details. ISO/JIS type ASME/ANSI/AGD type
元のページ ../index.html#360