MEASURING INSTRUMENTS CATALOG No.E2021
406/604

F-65FMitutoyo reserves the right to change any or all aspects of any product specication, including prices, designs and service content, without notice.Replacing bezels and graduation platesA bezel and graduation plate must be swaged together so that the graduation plate always rotates with the bezel. Assemblies comprised of a swaged bezel and graduation plate are available for some models.Order No. of dial indicatorsOrder No. of swaged assemblies2046A21AZB6502109A-1021AZB6932046S21AZB1322109S-1021AZB138Set order No. 7823EUSet Conguration(1) Spindle rest (129730)(2) Pin remover (129732)(3) Punch (129733)(4) Bearing adjuster (129734)(5) Pinion rest (129735)(6) Reamer (ø1: 1/50 taper) (129736)(7) Reamer (ø0.6: 1/50 taper) (193702)(8) Reamer for pointer (ø0.5: 1/20 taper) (21JAA273)(9) Pointer removing tool (126628)(10) Soft touch pliers (21JAA371)(11) Nippers (901179)(12) Pin rest (129731)(13) Hammer (901178)(14) Stick (21JAA314)(15) Brush (901177)(16) Bamboo brush (901176)(17) Pin-vise (901175)(18) Screwdriver (Phillips/at blade) (901174)(19) Tweezers (129729)(20) Screwdriver (Phillips) (901173)(21) Pointer removing tip (ø0.8) (126630)(22) Pointer removing tip (ø0.5) (126630B)(23) Pointer removing tip (ø1.6) (126630C)(24) Adjustable nut (100699)Typical applicationsRemove the long handPosition the pointer removing tool (No. 9) on the hole diameter of the minute hand. Push the pivot with the pointer removing tool to remove the long hand.Remove the little hand Remove the little hand with the nippers (No. 11). Adjust a bearingPress the steel or jeweled bearing into its housing using the bearing adjuster (No. 4).Remove or replace a pinPlace the spindle on the groove of the spindle rest (No. 1). Remove the pin with the pin remover (No. 2) and the hammer (No. 13). Tap the pin directly with the hammer (No. 13) to replace the pin.Replace the long or little hand Screw the pinion rest (No. 5) into the pin rest (No. 12). Support the pinion with the xed pinion rest, and replace the hand with the punch (No. 3) and hammer (No. 13). Reaming is necessary when replacing with a new hand. Use reamers as follows:• The hands of DG Series A-type and TI-X Series*1 dial test indicators do not require reaming.• Use the reamer for pointer (No. 8) (ø0.5: 1/20 taper) for S type and T type dial indicators*2.• Depending on the shaft diameter, use reamer (No. 6) (ø1: 1/50 taper) or reamer (No. 7) (ø0.6: 1/50 taper) for F type dial indicators and other than TI-X Series dial test indicators. *1 Dial test indicator whose model No. ends in “X”.*2 Dial indicator whose order No. includes an “S”, “T” and “A”.Order No. 7000• Used for tting a crystal on dial indicators (1003, 1911, 1913-10, 1003T, 1911T-10, 1913T-10, and 4046S) and dial test indicators (pocket type) with a non- integrated molded crystal. • 8 sizes of crystal setting pads are supplied as standard. • Typical applicationsNos. 2 and 3: Bezel outside diameter of approx. ø28 Nos. 3 and 4: Bezel outside diameter of approx. ø35• Size of crystal setting pads (mm)(1) ø19.5 (2) ø22.5 (3) ø25.5 (4) ø28.5 (5) ø32.5 (6) ø35 (7) ø38 (8) ø50• Crystal setting pads set (including No. 1 to No. 8): 21JAA032Note: Crystal setting pads for large dial indicators (SERIES 3 and 4) are available by special order.Dial Indicator Crystal SetterDial Indicator Repair Tool Kit(7)(1) (2) (3) (4) (5) (6)(8)Dial IndicatorsComparison measuring instruments which ensure high quality, high accuracy and reliability.(24)(12)(19)(18)(4)(2)(3)(20)(1)(10)(16)(5)(22)(23)(9)(11)(6)(7)(8)(17)(14)(13)(15)(21)

元のページ  ../index.html#406

このブックを見る