F-45FMitutoyo reserves the right to change any or all aspects of any product specication, including prices, designs and service content, without notice.Dial IndicatorsComparison measuring instruments which ensure high quality, high accuracy and reliability.An inspection certicate is supplied as standard. Refer to page U-11 for details.DIMENSIONSUnit: inUnit: mm取付けねじM2.5×0.45φ6.5φ6.5φ4AφH5BGFφC16DEφ8 0-0.009Iφ8 0-0.009φCφH16(13)IEDFG5φ4AB(取付部:M2.5×0.45)パーツNo.21AZA319ボール付測定子 先端ø3(1911,1913-10)F-40-1ø6.5Iø4øH5BA16ø8 0-0.009EDFøCG(取付部:M2.5×0.45)パーツNo.21AZA319ボール付測定子 先端ø3(1003)F-40-2ø6.5ø4IøHEDABGFøC513ø8 0-0.009M2.5×0.45ø6.5Iø4øH5BA16ø8 0-0.009EDFøCGM2.5×0.45ø6.5ø4IøHEDBGFøC513ø8 0-0.009A4-48UNFø0.26Iø0.16øH1/4BA0.63ø0.375 0-0.0012EDFøCG1911T-10/1913T-101921T-10/1923T-10/1925T-101003TSPECIFICATIONSMetricOrder No.Graduation (mm)Range (range/rev) (mm)Accuracy* (µm)Repeat-ability (µm)Dial readingMeasuring force (N)w/lugFlat-backMeasuring rangeRetrace1/10 Rev1 Rev1911T-101911TB-100.012.5 (1)12481030-50-01.8 or less1913T-101913TB-100.0020.5 (0.2)62.52.5510-100-01.8 or less1003T1003TB0.014 (1)13481130-50-01.4 or less ISO/JIS typeMetricUnit: mmOrder No.ABCDEFGHIMass (g)w/lugFlat-back1911T-1015.5423112.919.21511.5305.956521913T-1015.539.53112.919.215 9305.956521003T1840.3361315  9.512.83266158InchUnit: inOrder No.ABCDEFGHIMass (g)w/lugFlat-back1921T-100.611.571.220.51 3/40.590.371.180.2756521923T-100.611.511.220.51 3/40.590.311.180.2756521925T-100.611.481.220.51 3/40.590.281.180.275652Note 1: Limit hands, bezel clamps and lifting levers cannot be installed.Note 2: The shoulder on a contact point (standard accessory) acts as a stop to prevent spindle overrun that may otherwise damage the indicator. For this reason, if you need to install an optional contact point with an outside diameter smaller than 7 mm, use a washer (with outside diameter of at least 7 mm, inside diameter of 3 mm, and thickness of approx. 0.5 mm) placed between the contact point and the spindle.Note 3: Being xed by only two retaining screws, the back cannot be rotated by 90 degrees to change the orientation of the lug.InchOrder No.Graduation (in)Range (range/rev) (in)Accuracy* (in)Repeat-ability (in)Dial readingMeasuring force (N)w/lugFlat-backFirst 1 Rev/2.5 Rev/10 RevRetrace1921T-101921TB-100.0010.1 (0.04)±0.001/±0.001/—0.0002±0.00020-20-01.8 or less1923T-101923TB-100.00050.05 (0.02)±0.0005/±0.005/—0.00016±0.00010-10-01.8 or less1925T-101925TB-100.00010.025 (0.01)±0.0002/±0.0002/—0.0001±0.000030-5-01.8 or less ANSI/AGD type* Completed products inspection is performed in the vertical orientation (contact point downward) and the stated accuracy is guaranteed.* Completed products inspection is performed in the vertical orientation (contact point downward) and the stated accuracy is guaranteed.

元のページ  ../index.html#384